Changes

Put on long sleeves, long pants, your goggles, and gloves.  If you have long hair, tie it back.  Keep a bottle of white vinegar on hand, and if any lye comes in contact with your skin, douse the area with vinegar, which, being highly acidic, neutralizes the alkaline lye.

Put on long sleeves, long pants, your goggles, and gloves.  If you have long hair, tie it back.  Keep a bottle of white vinegar on hand, and if any lye comes in contact with your skin, douse the area with vinegar, which, being highly acidic, neutralizes the alkaline lye.

Place your pot on the scale and record how much it weighs so you will be able to subtract its weight later, or if your scale has a tare feature, press the tare button and the scale will reset to zero.  Slowly pour the olive oil into the pot until the scale reads 1.5 pounds. Remember to subtract the pot’s weight if the scale does not have a tare feature.  Add one ounce of beeswax.  Heat the beeswax and oil to 120o F and set the pot aside.

Place your pot on the scale and record how much it weighs so you will be able to subtract its weight later, or if your scale has a tare feature, press the tare button and the scale will reset to zero.  Slowly pour the olive oil into the pot until the scale reads 1.5 pounds. Remember to subtract the pot’s weight if the scale does not have a tare feature.  Add one ounce of beeswax.  Heat the beeswax and oil to 120^oF and set the pot aside.

Weigh 10 ounces of water in the pitcher.  Remove the pitcher from the scale and weigh 4 ounces of lye in the small dish.  Be very careful because lye can cause severe burns.  Slowly pour the lye in to the water, stirring to dissolve the crystals.  Don’t pour the water onto the lye or they will react violently.  The water and lye will heat up to a high temperature.  Be careful not to breathe the fumes coming from the solution.  Use the second thermometer to measure the lye and water mixture’s temperature.  Wait until the solution cools to 120o F.   

Weigh 10 ounces of water in the pitcher.  Remove the pitcher from the scale and weigh 4 ounces of lye in the small dish.  Be very careful because lye can cause severe burns.  Slowly pour the lye in to the water, stirring to dissolve the crystals.  Don’t pour the water onto the lye or they will react violently.  The water and lye will heat up to a high temperature.  Be careful not to breathe the fumes coming from the solution.  Use the second thermometer to measure the lye and water mixture’s temperature.  Wait until the solution cools to 120^oF.   

As the lye is cooling, grease the container you are using as a mold with vegetable shortening, and put a piece of freezer paper on the bottom.  Some soapmakers prefer to line the mold with a plastic garbage bag.  Both methods work well, so use whichever one is easier for you.  If you use a garbage bag, make sure it lies flat in the mold so your soap will be smooth.

As the lye is cooling, grease the container you are using as a mold with vegetable shortening, and put a piece of freezer paper on the bottom.  Some soapmakers prefer to line the mold with a plastic garbage bag.  Both methods work well, so use whichever one is easier for you.  If you use a garbage bag, make sure it lies flat in the mold so your soap will be smooth.

When the lye solution cools to 120o F, slowly add it to the pot of oil and beeswax while stirring briskly.  Continue stirring the soap until it begins to thicken.  Occasionally test the soap’s thickness by scooping up a little soap and allowing it to drip off a spoon into the soap mixture.  When the soap leaves a small bump on the surface of the solution before sinking back in, the soap has reached the stage called “trace”.  If you are adding scents or colorings to your soap, add them at this point, and stir them in thoroughly.

When the lye solution cools to 120^oF, slowly add it to the pot of oil and beeswax while stirring briskly.  Continue stirring the soap until it begins to thicken.  Occasionally test the soap’s thickness by scooping up a little soap and allowing it to drip off a spoon into the soap mixture.  When the soap leaves a small bump on the surface of the solution before sinking back in, the soap has reached the stage called “trace”.  If you are adding scents or colorings to your soap, add them at this point, and stir them in thoroughly.

Pour the soap into the mold and put the lid on the container.  Wrap the mold in the towel and put it in an undisturbed area for 18 hours.  Remove the towel and leave the soap for another two hours.  Put on your gloves and turn the soap out of the mold.  The soap still needs to cure and may be mildly caustic.  Let the block sit for a day or two before you slice the soap into bars.  Once you have sliced the bars, put them in a well ventilated box so that they do not touch each other and leave them for two weeks or longer.  The longer the soap cures, the harder and milder it will be.

Pour the soap into the mold and put the lid on the container.  Wrap the mold in the towel and put it in an undisturbed area for 18 hours.  Remove the towel and leave the soap for another two hours.  Put on your gloves and turn the soap out of the mold.  The soap still needs to cure and may be mildly caustic.  Let the block sit for a day or two before you slice the soap into bars.  Once you have sliced the bars, put them in a well ventilated box so that they do not touch each other and leave them for two weeks or longer.  The longer the soap cures, the harder and milder it will be.